Logitech quickcam messenger driver vista

#Logitech quickcam messenger driver vista mac os x
#Logitech quickcam messenger driver vista drivers
#Logitech quickcam messenger driver vista pro
#Logitech quickcam messenger driver vista software
#Logitech quickcam messenger driver vista professional

I tried this, always with an XP SP3 VM, also in Parallels Desktop 4 Beta and in VirtualBox (the latest release, version 2.0.4), and got mixed results: it works well in Parallels (albeit only with the trick to disconnect and reconnect after the first hardware detection, which anyway gives an error instead of hanging) it doesn't work at all in VirtualBox (of course with USB 2.0 enabled), which gives this error: USB device 'Logitech Camera' with UUID is busy with a previous request.

#Logitech quickcam messenger driver vista drivers

(In a Vista VM everything works well with the Logitech drivers and software, as I said before.)ДЄh, good to know that it is a known problem. I also tried to uninstall the Logitech drivers and test the webcam in basic UVC mode in XP: here, it is correctly detected - without hangs and thus without the need to disconnect and reconnect it during the new hardware found process - and the built-in Windows drivers are correctly installed, working as they should but the whole point in using Windows for this webcam is to take advantage of the full-featured Logitech software, so using it only in basic UVC mode is of course better done directly within OS X. P.S.: I have attached two screenshots of some of the problems described above (the webcam icon in the Fusion status bar is also visibile, and has the icon of a headset: maybe this could also be improved, with a more realistic icon). Have you been able to reproduce this internally? Could it be some form of driver-related conflict between XP, Fusion and maybe also OS X? Etc.

#Logitech quickcam messenger driver vista software

I also tried to apply the MS hotfix described here on the Logitech forums for a rather similar case (a hotfix which installs a new XP Usbehci.sys file, version 'SP4'), but that didn't work either: still no camera detected in the QuickCam software (and of course the same happens in Windows Live Messenger and Skype), and still no driver reported as installed in the respective General tabs in Device Manager.

#Logitech quickcam messenger driver vista professional

0, that is the latest drivers from the latest QuickCam 11.8 software - so, essentialy, the correct drivers are reported as not installed (in the General tab) and installed (in the Driver tab) at the same time! Very strange.ДЄll on a fresh and fully patched Windows XP Professional SP3 Italian install, with still very few other programs added (so there should be no conflicts).

I incorrectly said that in the Device Manager it says that no driver is loaded (in the first, General tabs of the webcam and microphone properties): well, in reality it says that no driver is installed, while in the Driver tabs it correctly says (in both cases) that the driver is Logitech from version.

#Logitech quickcam messenger driver vista mac os x

The host system is Mac OS X Leopard 10.5.5 on a Mac mini with 4 GB RAM (512 MB dedicated to XP and 1 GB to Vista).ДЄn update. In Mac OS X, the webcam works in basic mode, through the built-in UVC (USB Video Class) driver: and even so, the image is very good. In Vista, as I said, everything works perfectly: but of course I'd prefer to use the webcam and its full-featured Windows-only Logitech software (in Unity mode) through XP, as it is less resource hungry than Vista (the webcam has some tough system requirements). I know there have been other similar reports regarding Logitech webcams, but a solution doesn't seem to have been found, yet. So, essentially, the webcam doesn't work: is this a Fusion problem? or an XP problem? or both?

#Logitech quickcam messenger driver vista pro

There is a problem with this webcam and VMware Fusion 2.0 with a Windows XP SP3 guest (while it works OK with a Windows Vista guest): following the QuickCam software installation instructions, when it is time to plug in the webcam (through USB 2.0) it is indeed detected by XP as a Logitech QuickCam Pro 9000, but then the new hardware icon remains in the tray without any further progress if one disconnects and then reconnects the webcam via the Fusion status bar, the installation completes (and thus it also detecs the built-in microphone), but after the installation the webcam doesn't work and isn't detected within the QuickCapture software in the Device Manager everything seems to be OK (both the camera and the microphone are present and working, and without any yellow problem badge), but it says that no driver is loaded (while the correct drivers are indeed installed) disconnecting and reconnecting apparently also works, with the usual sounds and no new hardware messages, as if everything were OK.